Steel Belt Lacings

BOLINJKAR Steel Lacings are packed in boxes complete with G.I. hinge pins. Specific use of "BOLINJKAR " Steel Lacings - alligator type on rubber, canvas, nylon & polyester belting of different sizes.

MANUFACTURED IN THIRTEEN SIZES

The small sizes-00 : 
A-1, A-7, A-10 are suitable for joining the Tape belts and webbeing up to 3.00 mm thick. These are mostly used in printing plants, Laundries etc. 

Number 15 to 75 :
 are suitable for joining all flat canvas / polyster / rubber belts from 3. mm to 16 mm thick.

The Belt Lacings :
 is indented under top face so that it may easily be broken to take narrower belts.

Compression :
 When "Bolinjkar" is applied, the compression grip will project the belt-ends and wil eliminate ply separation on rubbber / polyster / canvas belting.

Separate Joint :
 By removing the double hinge-pins the joint can be separated immediately.

"BOLINJKAR" is smooth on both faces, which is important where idler pulleys are concerned.
     
 
Select correct length of lacings (i.e. Less one teeth of both sides)   Bend lacings fully. Repeat it twice or trice till it break off.
     
 
Insert the lacings in proper position of the belt till the guage pin tauches it. Press the lacing with the help of hammer on a wooden / Iron stoppage.   Confirm the fitting of lacings carefully
     
SBL No. 00:-
For tape, nylon & knitted belts upto 1.5 mm. thick in boxes containing six sets for 15 cm. and above in length Complete with hinge-pins.
   
SBL No. A1:-
For tape belts 1.5 mm. to 2.5 mm. thick in boxes containing six sets for 15 cm. and above in length Complete with hinge-pins.
   
SBL No. A7:-
For tape belts 2.5 mm. to 3.00 mm. thick in boxes containing six sets for 15 cm. and above in length Complete with hinge-pins.
   
SBL No. A10:-
For tape belts 1.5 mm. to 3.00 mm. thick for extra deep grip. In boxes containing six sets for 15 cm. and above in length belts. Complete with hinge-pins.
   
SBL No. 15:-
For belts 3 mm. to 4 mm. thick in boxes containing Eight sets for 20 cm. and above in length Complete with hinge-pins.
   
SBL No. 20:-
For belts 4 mm. to 5 mm. thick in boxes containing five sets for 30 cm. and above in length Complete with hinge-pins.
   
SBL No. 25:-
For belts 5 mm. to 6 mm. thick in boxes containing eight sets for 30 cm. and above in length Complete with hinge-pins.
   
SBL No. 27:-
For belts 6 mm. to 7 mm. thick in boxes containing eight sets for 30 cm. and above in length Complete with hinge-pins.
 
SBL No. 35:-
For belts 7 mm. to 8 mm. thick in boxes containing four sets for 30 cm. and above in length Complete with hinge-pins.
   
SBL No. 45:-
For belts 8 mm. to 9 mm. thick in boxes containing four sets for 30 cm. and above in length Complete with hinge-pins.
 
SBL No. 55:-
For belts 9 mm. to 11 mm. thick in boxes containing four sets for 30 cm. and above in length Complete with hinge-pins.
   
SBL No. 65:- For belts 11 mm. to 13 mm. thick in boxes containing four sets for 30 cm. and above in length Complete with hinge-pins.
SBL No. 75:- For belts 13 mm. to 16 mm. thick in boxes containing four sets for 30 cm. and above in length Complete with hinge-pins.
 
Press the lacngs at other end uniformally. Confirm that the fitting of pair should be in parallel position.
 
 
Always take a pair of hinge pins & adjust.(Length of Hinge pins according to the Lacings).
 
 
Insert pair Hinge pins
 
 
The fitting of the Belt Lacings is completed and belt is now ready for use
     
     
 
     Our Products
 
 
 
 
     Navigation
Home
Profile
Products
Actual User
Available Here
Price List
Contact Us
Feedback
Site Map
 
 
 
Contact Details - MR. ASHOK CHAPHEKAR - DIR
Address -
13/17, Petit Compd, Nana Chowk, Frere Bridge Low Level (South), Grant Rd, Mumbai- 400007
Tel. - 022 23889898 / 23877168 |       Fax - (022) 23890544   |    Mob. - +91 86528 35000
 
Steel Belt Lacings | Plate Type Conveyor Belt Fasteners